A Bare Stranded Copper Conductor
B Okoseal Insulation/Nylon
Jacket
C Twisted, Shielded Pairs/Triads
D Aluminum/Synthetic Polymer
Face
E Tinned Stranded Copper Drain
Wire
F Rip Cord
G Inner Black Okoseal Jacket
H Impervious, Continuous,
Corrugated Aluminum C-L-X Sheath
J Outer Black Okoseal
Jacket
Specifications
Conductors: Bare soft annealed copper, Class B, 7-strand concentric
per ASTM B-8.
Insulation: Flame-retardant Okoseal (PVC) per UL 83, 15 mils
nominal thickness, 90°C temperature
rating.
Jacket: Nylon per UL 83, 4 mils nominal thickness.
Conductor Identification: Pigmented black and white in pairs;
black, white and red in triads.
Assembly: Pairs or triads assembled with left-hand lay. Non-wicking
fillers included where required to provide a round cable.
Cable Shield: Aluminum/Polyester tape overlapped to provide 100%
coverage, and a 7-strand tinned copper drain wire, same size as conductor.
Inner Jacket: Black, flame-retardant Okoseal per UL Standard 1569.
A rip cord is laid longitudinally under the jacket to facilitate removal.
C-L-X Sheath: A close-fitting, impervious, continuously welded and
corrugated, aluminum sheath meeting UL 1569 provides complete protection
against moisture, liquids, and gases, has excellent mechanical strength,
and provides equipment grounding through the sheath.
Outer Jacket: Black, flame-retardant Okoseal per UL Standard 1569.
Classifications: UL Listed as Type MC-HL Articles 501, 502, 503,
504 and 505 of the National Electrical Code.
Applications
Okonite C-L-X Single pair or triad type P-OS instrumentation
cables are designed for use on Class 1 Remote-Control Signaling circuits
or where a 600V cable is desired, as instrumentation, process control, or
computer cable transmitting signals at levels above 100 milli-volts in
circuits where shielding against external interference is required, but
shielding against interference among groups is not required. For use
indoors or outdoors; wet or dry locations; in cable trays; in raceways;
supported by a messenger wire; for direct burial; in Classes I, II, and
III, Divisions 1 and 2 hazardous locations per NEC Articles 501, 502, 503,
504 and 505. Listed by American Bureau of Shipping (ABS) as CWCMC-MC-HL
and by UL as marine Shipboard. Also for use as non power limited fire
protective signaling cable (NPLF) per NEC Code 760.
The overall shield eliminates most of the static interference from the
electric field radiated by power cables and other electrical equipment.
The C-L-X sheath provides the physical protection against mechanical
damage as required in NEC Section 725-8 as well as complete protection
against moisture or gases entering the cable.
For dc service in wet locations, X-Olene insulation is recommended.
These cables also comply with UL requirements for Types CL2 and CL3.
Product Features
- UL listed for cable tray use, direct burial and sunlight resistant.
- Passes the IEEE 383-1974 and IEEE 1202-1991 vertical tray flame
tests.
- Passes the 210,000 BTU Vertical Tray Flame Test utilizing the corner
configuration and the ICEA T-29-520 Vertical Tray Flame Test.
- Complete pre-packaged, factory-tested wiring system color coded.
- C-L-X enclosure permits installation in cable tray containing light
and power cables without a barrier separator.
- Impervious, continuous sheath excludes moisture, gases and liquids.
- C-L-X sheath exceeds equipment grounding conductor requirements of
NEC Section 250-95.
- Excellent compression and impact resistance.
- Lower installed system cost than conduit or EMT systems.
- OSHA Acceptable.
- Complies with Articles 501, 502, 503, 504 and 505 for hazardous
locations.
- UL listed as Type MC-HL and Marine Shipboard cable.
- American Bureau of Shipping listed as CWCMC Type MC-HL.
- Recognized by US Coast Guard as Type MC and CWCMC.
- Suitable for low temperature installation to -40°C.
- Meets API Standards 14 F and 14F2.
|
564-60-3401